4 Popular Methods of Dry-Hopping Your Beer in brewery
- Feb 16, 2022
- 64
- tiantai
How to Dry Hop
The basic process of dry hopping, and one of the most common methods, is to simply siphon your beer out of your primary fermenter into a secondary fermenter and add hops. It is typically best to place your hops in a hop bag or other strainer in which they can be contained and still be in contact with your beer.
If your hops are whole cone hops, you can add them directly into the beer and siphon them off later, but doing so with pellet hops can result in excess hop matter being siphoned into your final packaging.
That’s the basic method. We’ll get into some fun variations here in a minute, but first we need to talk hop selection and dry hop duration.
Choosing the Right Hop Variety
The best way to choose the right hop or hops for dry hopping is to use the hops added to the recipe as aroma hops to begin with. So, if your latest hop addition in the beer was Centennial hops, try dry hopping with Centennial hops.
Alternately, you can dry hop with a complimentary hop. Again, if your last hop addition was Centennial, you can try another “C” hop, such as Cascade or Citra. The citrus aromas will work well together without clashing.
If your pale ale uses three different hops late in the boil, you can blend them when dry hopping.
Finally, for best results, you should dry hop with lower alpha acid hops when possible. Higher alpha acid hops tend to have a lower percentage of the delicate aroma oils you are going for, so using lower AA hops is really just more efficient.
You can get great results with higher AA hops, however, so this is a guideline, not a rule.
How Long to Dry Hop?
Dry hopping is a fantastic way to get the aroma into your beer, but how long is long enough? How long is too long?
Hops added to secondary post fermentation can add significant levels of aroma in 24 hours, and it improves for at least 48-72 hours.
After that amount of time, you will still get added aroma, but not as quickly. Some brewers will leave hops in their fermenters for the entire secondary fermentation, but if this will be more than a couple of weeks, this can result in vegetal flavors, such as “grassy” notes or other off flavors.
You can leave hops in the fermenter for a week or two before the off flavors really start to develop. You won’t get a significant increase in hop aroma over the first 72 hours, but if you just can’t get to packaging in that time, it won’t hurt the beer. After 2-3 weeks, it’s really time to get the beer off your hops or you’ll start to see the bad flavors develop.
So, the ideal amount of time is about 48-72 hours. After that, package it up.
4 Common Ways to Dry Hop Your Beer
Now that we’ve outlined the basics, let’s talk about some variations on the theme. There are a lot of ways to “dry hop” your beer, and some of them are pretty cool and fun. Some are not very practical, but are fun for the novelty.
How to Dry Hop Your Beer
The French Press
This dry-hopping technique is not the ideal method, but it can be a quick way to determine what aroma compounds will work with a certain type of beer.
Let’s say you have a pale ale you brewed that you are considering dry hopping next time. Add some pale ale to some pellet hops in your French Press and give it some contact time.
Then, press the plunger and pour the beer. It will be slightly flatter, as the pressing will excite some carbon dioxide out of suspension, but you should be able to get a good idea of what that specific hop will contribute to your next batch.
Keg Hopping
This is a good variation on dry hopping in which the hops are added to a hop bag or tea strainer and added directly to the keg. This method really imparts significant hop aroma, as the strainer will sit right next to the beer uptake and some of the beer will pass right through the bag on its way to your glass, resulting in a very fresh taste.
Unfortunately, this method means you really need to consume the beer within a 2-3 week period or you’ll start to taste the grassy and vegetal notes we discussed earlier. This method is fantastic for parties and one time events, though.
The Randall
Pioneered by Dogfish Head Brewing, The Randall is a device that hooks to your tap lines and allows you to push your beer directly through a sample of whole hops.
The concept is that you have a chamber in which you add dried or fresh whole cone hops which seals well. The beer line runs into this chamber on one side and out of the chamber on the other. The beer comes in direct contact with the hops on its way to your glass, taking delicate aroma compounds with it.
This system does work well, but requires a kegerator and specialized equipment. You can build your own Randall if you have a kegerator or you can order one from Dogfish Head on their website.
Dry Hopping during Primary
Most homebrewers’ first reaction to this is that it is not as efficient as dry-hopping in secondary. The theory is that dry-hopping in primary allows carbon dioxide bubbles to carry off the aroma compounds from the beer.
The truth is that, while hopping in primary does change the aroma profile, the true mechanism for why that happens is not yet completely understood.
The aroma compounds from hops are contained in the hop oils, which are not volatile enough to be carried off by CO2 bubbles. The only reason they dissipate in the boil is because they are, well, boiled. This process is being experimented with some at the homebrew and commercial brewing levels, but has not yet caught on in full. The anecdotal evidence seems to point to this method changing the aroma compounds contributed, but does not necessarily reduce them.
Now that you have a little more info on the methods of dry-hopping, it’s time to give it a try. Experiment with your dry-hopping techniques and see what works best for your recipe.
So, maybe the next step will be to brew a batch of beer and split into two batches. You could dry hop one in primary and one in secondary, then bottle them up and taste them with friends. After all, that’s the best way to taste beer.
Derrick
Sales Manager
[email protected]
Tiantai Beer Equipment
The basic process of dry hopping, and one of the most common methods, is to simply siphon your beer out of your primary fermenter into a secondary fermenter and add hops. It is typically best to place your hops in a hop bag or other strainer in which they can be contained and still be in contact with your beer.
If your hops are whole cone hops, you can add them directly into the beer and siphon them off later, but doing so with pellet hops can result in excess hop matter being siphoned into your final packaging.
That’s the basic method. We’ll get into some fun variations here in a minute, but first we need to talk hop selection and dry hop duration.
Choosing the Right Hop Variety
The best way to choose the right hop or hops for dry hopping is to use the hops added to the recipe as aroma hops to begin with. So, if your latest hop addition in the beer was Centennial hops, try dry hopping with Centennial hops.
Alternately, you can dry hop with a complimentary hop. Again, if your last hop addition was Centennial, you can try another “C” hop, such as Cascade or Citra. The citrus aromas will work well together without clashing.
If your pale ale uses three different hops late in the boil, you can blend them when dry hopping.
Finally, for best results, you should dry hop with lower alpha acid hops when possible. Higher alpha acid hops tend to have a lower percentage of the delicate aroma oils you are going for, so using lower AA hops is really just more efficient.
You can get great results with higher AA hops, however, so this is a guideline, not a rule.
How Long to Dry Hop?
Dry hopping is a fantastic way to get the aroma into your beer, but how long is long enough? How long is too long?
Hops added to secondary post fermentation can add significant levels of aroma in 24 hours, and it improves for at least 48-72 hours.
After that amount of time, you will still get added aroma, but not as quickly. Some brewers will leave hops in their fermenters for the entire secondary fermentation, but if this will be more than a couple of weeks, this can result in vegetal flavors, such as “grassy” notes or other off flavors.
You can leave hops in the fermenter for a week or two before the off flavors really start to develop. You won’t get a significant increase in hop aroma over the first 72 hours, but if you just can’t get to packaging in that time, it won’t hurt the beer. After 2-3 weeks, it’s really time to get the beer off your hops or you’ll start to see the bad flavors develop.
So, the ideal amount of time is about 48-72 hours. After that, package it up.
4 Common Ways to Dry Hop Your Beer
Now that we’ve outlined the basics, let’s talk about some variations on the theme. There are a lot of ways to “dry hop” your beer, and some of them are pretty cool and fun. Some are not very practical, but are fun for the novelty.
How to Dry Hop Your Beer
The French Press
This dry-hopping technique is not the ideal method, but it can be a quick way to determine what aroma compounds will work with a certain type of beer.
Let’s say you have a pale ale you brewed that you are considering dry hopping next time. Add some pale ale to some pellet hops in your French Press and give it some contact time.
Then, press the plunger and pour the beer. It will be slightly flatter, as the pressing will excite some carbon dioxide out of suspension, but you should be able to get a good idea of what that specific hop will contribute to your next batch.
Keg Hopping
This is a good variation on dry hopping in which the hops are added to a hop bag or tea strainer and added directly to the keg. This method really imparts significant hop aroma, as the strainer will sit right next to the beer uptake and some of the beer will pass right through the bag on its way to your glass, resulting in a very fresh taste.
Unfortunately, this method means you really need to consume the beer within a 2-3 week period or you’ll start to taste the grassy and vegetal notes we discussed earlier. This method is fantastic for parties and one time events, though.
The Randall
Pioneered by Dogfish Head Brewing, The Randall is a device that hooks to your tap lines and allows you to push your beer directly through a sample of whole hops.
The concept is that you have a chamber in which you add dried or fresh whole cone hops which seals well. The beer line runs into this chamber on one side and out of the chamber on the other. The beer comes in direct contact with the hops on its way to your glass, taking delicate aroma compounds with it.
This system does work well, but requires a kegerator and specialized equipment. You can build your own Randall if you have a kegerator or you can order one from Dogfish Head on their website.
Dry Hopping during Primary
Most homebrewers’ first reaction to this is that it is not as efficient as dry-hopping in secondary. The theory is that dry-hopping in primary allows carbon dioxide bubbles to carry off the aroma compounds from the beer.
The truth is that, while hopping in primary does change the aroma profile, the true mechanism for why that happens is not yet completely understood.
The aroma compounds from hops are contained in the hop oils, which are not volatile enough to be carried off by CO2 bubbles. The only reason they dissipate in the boil is because they are, well, boiled. This process is being experimented with some at the homebrew and commercial brewing levels, but has not yet caught on in full. The anecdotal evidence seems to point to this method changing the aroma compounds contributed, but does not necessarily reduce them.
Now that you have a little more info on the methods of dry-hopping, it’s time to give it a try. Experiment with your dry-hopping techniques and see what works best for your recipe.
So, maybe the next step will be to brew a batch of beer and split into two batches. You could dry hop one in primary and one in secondary, then bottle them up and taste them with friends. After all, that’s the best way to taste beer.
Derrick
Sales Manager
[email protected]
Tiantai Beer Equipment
.jpg)